離合器是機械式傳動裝載機中易損壞的關鍵部件之一，正確使用妥善保養，可以延長其使用壽命。如使用不當，容易導致發生故障。離合器在使用過程中，由于零件的不斷磨損，特別是離合器從動盤上摩擦片的磨損，都會改變分離杠桿與分離軸承端面的間隙，此間隙過大會造成踏板踩到底也分離不開；間隙過小會產生分離軸承始終隨分離杠桿轉動，而很快地?zé)龎幕蚰p。此外在使用過程中，由于三個分離杠桿變形、磨損的不同，會造成三個分離杠桿不同在一個與花鍵軸垂直的平面內，也就使得離合器分離不徹底，換檔困難、很快會將變速器的換檔齒輪打壞。離合器分離不徹底也加速摩擦片的磨損，降低離合器的使用壽命。

Clutch is one of the key components of the mechanical drive loaders are easily damaged , and the proper use of proper maintenance , you can extend its life. If used improperly, easily lead to failure. Clutch during use , due to the constant abrasion of parts, in particular the wear of the clutch driven plate friction plate will change. Variable separation and separation gap lever bearing end face , the gap caused by pedal in the end over the General Assembly also points inseparable ; gap is too small will produce consistently with the separation lever release bearing rotation, and quickly burn out or wear. Also in use , the three separate lever deformation, wear of different causes three stars. Different from the lever in the plane perpendicular to the axis of a spline , also makes the clutch is not complete , shifting difficulties , the transmission will shift gears quickly broke . Clutch is not complete but also accelerate the wear of the friction plate and reduce the life of the clutch. Clutch is one of the key components of the mechanical drive loaders are easily damaged , and the proper use of proper maintenance , you can extend its life. If used improperly, easily lead to failure.

小型裝載機-山東永保機械有限公司提醒大家使用裝載機離合器應注意以下要點：

1、離合器分離時間不宜過長，一般不超過15-20秒；
   Clutch release time not too long, not more than 15-20 seconds;

2、不要用離合器半分離的方法來控制車速，以免摩擦片和分離軸承迅速磨損。同時，在行駛時，不要把腳放在離合器踏板上。
   Do not use the clutch semi-detached approach to control speed to avoid friction plate and release bearing rapid wear. Also, when driving, do not put your feet on the clutch pedal.

3、分離離合器時，動作要迅速，踏板要踩到底，以求徹底分離；
   When separating clutch, action should be quick to step on the pedal in the end, in order to complete separation;

4、接合離合器時，應緩慢放松踏板，使之柔和平穩地接合；
   When engaging clutch pedal should be slow to relax, making soft smooth engagement;

5、保養內容有清潔殼體，檢查調整分離間隙、定期注入潤滑脂，必要時清洗摩擦片上的油漬。
   Maintenance contents clean shell, check and adjust the separation gap, regularly inject grease, cleaning grease on the friction plates when necessary.

山東裝載機：http://www.jmkey.cn/